Ford Transit High & Mid Roof Vent Adapter for 14" x 14" Opening

Description

WARNING!! Please verify the opening requirement on your Maxxair Fan.
If it is 400mm x 400mm you need to purchase an adapter from our Euro
Adapter listing https://www.ebay.com/itm/133005668147
Available now, Insulated Vent Fan Cover.
This fits a 14″ x 14″ opening. Please check your fan.
Patent
Pending adapter matches the contour of the OEM roof so a standard RV
style vent mounts to a flat surface.  Prevents distorting the roof sheet
metal or vent flange and can be used as an aid for locating the fan.
They are
CNC machined out of UV and fire resistant expanded PVC.
The fan mounts to the outside adapter.  Fan adapters work with the
Maxxair Deluxe series and the Fan-tastic Vent fans.
See our Interior Supporting Framing strips. They can be found under item number 143604536736
Please note that not all of the Transit vans are the same in the
Most Forward area and may require more glue if there is a gap or some
sanding on the adapter.
IMPORTANT
Fits a 14″ x 14″ opening.
Fan adapters work with the Maxxair Fan Deluxe series and the Fan-tastic Vent fans.
The outside adapter will fit anywhere along the cargo part of the roof. Longer screws than came with the vent fan may be needed.
The
vent adapter outside dimension is 16 3/4 X 16 3/4.   If you are using a
Maxxair vent our adapter fits the deluxe series, other Maxxair vents
have a wider flange. You will need a wider adapter. Please call.
The option with butyl tape includes 62″ of tape.
If
the butyl tape is stuck to the plastic, put it in the freezer for 30
minutes. It will release,  then let the butyl tape return to room
temperature.
We
make adapters to fit air conditioners and adapters for offset
locations. Please contact us so we can verify size and location.
Roof
Vent Adapter Install procedure: We recommend 3m Window-weld adhesive
which you can get at Napa. Locate and cut the 14 x 14 hole. You can use
the adapter as a guide to mark the hole. Stay clear of roof supports,
obviously. Make a tape line 1/4″ beyond the adapter perimeter. De-gloss
the area with a Scotch- brite pad. No need to scuff. Just dull the
paint. Clean with isopropyl alcohol and let dry thoroughly. Blow dryer
if it’s wet and/or cold out. Apply three 1/8″ beads of the Window-weld
on the face of the adapter. Then press the adapter down onto the roof
until the adhesive oozes out the sides. It’s not necessary to clamp. If
you do, use a lot of lightly set clamps and spread out the clamp force
over the whole surface area. Using the adhesive that oozes out, make a
fillet around the adapter with a double gloved finger. Pull the tape
within 15 minutes. Cure is fast on outside. Let cure overnight and then
proceed with the fan install. We recommend using butyl tape for the fan
install. Cover the fan flange with 1 1/8″ wide tape. Place onto of
adapter and press down. Then drill pilot holes through the adapter and
into the van roof. If the screws are going to go into a roof support
beam then drill a clearance hole in the beam. You only want the screw to
engage the adapter and outer skin. Use a step drill to keep from
plunging through the skin. You may need longer screws. Tighten them very
lightly against the fan flange. Some butyl will ooze out which you can
trim off. Coat the fan flange adapter and onto the roof about 1/2″ with
brush on bed-liner or Flexseal from the TV guy works well. Some sealants
will melt the fan plastic so you might try it on a portion of the
interior bezel first. You’ll cut a lot of that piece off. Good idea to
check the integrity and reapply the sealant every so often. Dicor self
leveling sealant also works but looks a little messy.
If you have questions about this product you can call Hein at 541-49O-5O98
Check out our
other items
!